Sitenotice: 11/29/2018: The wiki is back. It turns out, some anti-virus product on my web server had an issue with the latest version of PHP. My server techs have resolved this issue, and things should be working again. During the investigation, I did restore to a backup from September. There is a chance that any changes done since then were lost, but I do not recall any edits. --OS-9 Al
8/30/2016: Massive re-work is being done on the InfoBox Templates. Read that page to keep up with the plan for that, and adding better keyword tags (categories) to all the pages. --OS-9 Al (talk) 15:28, 31 August 2016 (CDT)
|Looking for CoCo help? If you are trying to do something with your old Color Computer, read this quick reference. Want to contribute to this wiki? Be sure to read this first. This CoCo wiki project was started on October 29, 2004. --OS-9 Al|
This page was last updated on 12/29/2014. Total Pages: 650. Total Files: 937.
J&M Systems, LTD. CoCo disk controller cart
Considered one of the best disk controllers for the TRS-80 Color Computers. They have gold connectors and are engineered to a very high standard
Internally has JDOS 1.11 rom on it for fast (6ms) disk drive stepping.
(8/7/12) I've just made a video of this great controller in action on my Coco 3: youtube J&M disk controller for Tandy TRS-80 Coco Color Computer
J&M Disk Controllers for Color Computer
J&M Sytems produced Disk Controllers and complete drive systems including a hard drive system. There were 3 different Controllers, the original JFD-COCO, the JFD-CP and the later JFD-EC. The JFD-COCO was not compatible with a CoCo3, the JFD-EC was introduced for the CoCo3. The JFD-CP features a parallel port to drive a Centronics compatible printer or the J&M hard drive.
This was the "classic" J&M controller. It had a 24 pin rom socket, that usually came with a JDOS rom in it. This controller had gold contacts on both ends of the board. Utilized a Synertek SY6591 controller chip, also socketed. This was a good controller till the CoCo3 came out, and it did not work with it. J&M initially recommended changing the 74LS04 to a 7404, but this did not always solve the incompatibility. The final modification was to substitute the Q clock signal in place of the E clock, basically a trace cut and adding a jumper. Simply cut the E clock line (Pad 6). Solder a jumper wire to the Q clock (Pad 7) and connect it to the controller. I used a through hole beside U17 to make the connection on one controller I modified. The controller will now work with the CoCo3 and the CoCo2. If you have a 24 pin JDOS rom, it will also not work with the CoCo3, swap in a RS DOS 1.1 or something such as ADOS 3. See Rainbow, May '87, page 174 for more information.
This was the second and most deluxe controller that J&M built for the CoCo. Externally it appears different than the original as there is now a toggle switch to select which rom to use, and a header connector which is the built in parallel port. The Hard Drive unit to connect to this controller was originally a 5 Mb Seagate, enclosed in a self contained drive/power unit with built in interface that connected directly to the Centronics compatible printer port. Software to drive it was OS-9 only.
JFD-CP Parallel Port
PIN FUNCTION SOURCE
1 Write Strobe Controller
3 D0 Bi-directional
5 D1 "
7 D2 "
9 D3 "
11 D4 "
13 D5 "
15 D6 "
17 D7 "
19 Read Strobe Controller
21 Busy External Device
25 Status External Device
26 Reset Controller
All even pins 2-24 are ground
This connector will allow most Centronics compatible printers to operate with the JFD-CP using a standard, unmodified Radio Shack Model 100 printer cable.
Pinout from page B-3, JDOS Disk Basic Reference Manual, J&M Systems
The EC stands for economy. This controller was brought out to get J&M back into the lower cost segment of the disk controller market. This controller has a toggle switch to select one of the dual roms, and now supports a 16K device. Cost savings were obtained by eliminating the parallel port , and utilizing the SY6591 controller chip, which J&M apparently bought the entire inventory of when Synertek went out of business.
Thanks to Alan Stallings, formerly of J&M, for correcting some errors and providing more information.
Page last updated Dec 24/2001